ENJaw Crusher Price: What Drives the Number in 2026
The 2026 price bands for Chinese-built jaw crushers, the five factors that move a specific quote, and the landed costs that never appear in it.
A small stationary jaw crusher built in a Chinese workshop quotes at $10,000-80,000 in 2026. A tracked mobile jaw plant quoted ex-works sits between $120,000 and $250,000, and the largest tracked primaries run to $400,000. All of those numbers are real, and none of them is a price. This page sets out the bands, the five variables that move a specific jaw crusher price inside them, and the landed costs that never appear in the ex-works figure at all.
The 2026 price bands
| Machine class | Capacity | 2026 price band (USD) | Notes |
|---|---|---|---|
| Small stationary jaw (PE-class) | 5-50 t/h | $10k-80k | Workshop build, crated for a container |
| Mid-size stationary jaw | 50-150 t/h | $60k-180k | Larger frame, heavier plates, still shippable in sections |
| Tracked mobile jaw plant | 100-250 t/h | $120k-250k | Diesel-hydraulic, quoted ex-works |
| Large tracked primary | 250-400+ t/h | $220k-400k | The biggest frames and engines in the class |
The windows describe Chinese-built equipment as suppliers quote it in 2026; a flagship European OEM equivalent can sit two to three times higher, and the gap is mostly brand, resale network and emission certification rather than capability. Scanning jaw crusher for sale listings online shows the spread inside a single class runs wider than the gap between classes, which is the tell that the five factors below, not the capacity figure, decide the number.
The five things that move the number
First, steel mass. Frame, chassis and flywheels are sold roughly by the tonne, so a 45-tonne production plant costs structurally more than a 30-tonne compact one. The extra steel is not padding: it is the margin between a machine that survives granite duty and one that cracks a frame in its second season. Transport weight is the fastest honest comparison between two quotes at the same capacity, because it is printed on the spec sheet and cannot be argued with.
Second, plate metallurgy. Mn13 is the baseline jaw plate grade; Mn18 carries a higher price per casting and lasts longer on abrasive feed, so the dearer set can be the cheaper cost per tonne. The grade decision follows the rock, and the trade-offs are set out in the guide to jaw plate material grades.
Third, engine emission stage. Stage III and Stage V packages are different machines at the paperwork level, and a Stage V engine can add $20,000-40,000 to the quote. Some destination markets require it, some never ask; paying for a certification the port does not request is money with no return.
Fourth, options. An over-band magnet, a pre-screen over the hopper, radio remote control and an onboard generator are each separate lines, and together they swing a quote by tens of thousands. Each earns its place only against a specific duty: the magnet where demolition steel is in the feed, the pre-screen where fines choke the chamber.
Fifth, order structure. A single machine, a matched jaw-and-screen train, consolidated shipping and a first-fill spares package each move the effective number. SUHMAN prices a matched train as one package, which usually lands below the sum of separate machine quotes, and the saving is real only if the train was specified as a train from the start.
The costs that never appear in the ex-works number
Shipping comes first. A crated stationary jaw fits a standard container, which is why small PE-class units move worldwide at container rates. A tracked plant does not: at around 15 m long and 40-plus tonnes it ships RORO or on flat racks, and freight, port handling and the overland leg to site are billed separately from ex-works.
Second, first-year spares. Budget two to four percent of machine value as wear-parts stock on the ground before the plant starts: a spare set of jaw plates, a toggle set, filters and hydraulic hoses. A plant stopped for a fortnight waiting on a casting costs more than the entire stock.
Third, duties and clearing. Tariff lines for crushing machinery are commonly low single digits, but bad paperwork costs storage fees and stopped commissioning while documents are corrected. Added together, the landed figure often runs 15-25% above the ex-works jaw crusher price, and that landed number, not the invoice, is what should be compared between suppliers.
How to get a number you can hold someone to
A quote that arrives without questions is a guess. The five facts below are what a serious supplier asks for first, and they are also what separate an honest jaw crusher price from an optimistic one.
- Feed material and its compressive strength in MPa: granite and basalt run 100-300 MPa, and the number decides plate grade and frame duty
- Maximum feed lump size in millimetres, and whether the feed arrives pre-screened
- Target capacity in tonnes per hour, and the product sizes in millimetres that the market pays for
- Site power: grid, genset or none, which decides the drive architecture
- Haul distance from port to site, which prices the overland leg and the low-loader
That is how SUHMAN quotes: feed sample first, target sizes and haul distance second, the number last. A supplier who skips straight to the price is quoting a machine, not a duty, and the difference shows up in month two.
The ex-works figure is a window into a market. The number you can hold someone to is the one that names the rock, the sizes and the spares.
Common questions
What does a tracked mobile jaw crusher cost in 2026?
Chinese-built tracked jaw plants quoted ex-works sit in a $120,000-250,000 window for the 100-250 t/h class in 2026, and the largest primaries run to $400,000. The exact figure moves with steel mass, engine emission stage, options such as magnets and pre-screens, and whether the order is a single machine or a matched train. Treat every published number as a market window, not a quote.
Is a cheaper jaw crusher for sale online really cheaper?
Not always. Listings at the bottom of the band usually mean lighter frames, thinner plates and shorter component life on abrasive feed. Compare transport weight and the wear parts list between two quotes at the same capacity: the honest machine is usually the heavier one with the longer parts list, and it costs less per tonne over three seasons.
What payment terms are normal with Chinese manufacturers?
A 30% deposit with the 70% balance due before shipment is the common structure, and larger suppliers can also work against letters of credit. Tie the balance to a factory acceptance test or shipping documents rather than a calendar date, and avoid full prepayment with any supplier, whatever discount is offered against it.
The plant-level picture continues in the guide to mobile crushing plant cost, including the hidden landed costs. Capacity figures machine by machine are on the jaw crusher range page, and for a number against actual rock and haul distance, send the five facts through the quote form.
