Compact tracked secondary cone
The SY-HP200 is the cone you put behind a small jaw when the product has to be saleable, not just broken. It takes 190 mm feed down to 8–44 mm at 120–280 t/h on a 37.3 t crawler chassis, with a 160 kW cone and a 100 kW engine. That discharge range covers the 10 mm and 20 mm aggregates a concrete plant actually orders.
A short walk-around filmed on a customer site — feeding, crushing and discharge, so you can see how the machine actually runs before you shortlist it.
Watch more videosGranite, basalt, andesite, gravel, iron ore, copper ore, etc.
Limestone, gravel, diabase, coal, etc.
Construction waste
A jaw alone gives you a sub-base product and a lot of oversize. The moment a customer wants clean single-size aggregate, a cone is the cheapest way to get there. It reduces by compression between two liners, so the particle shape stays cubical instead of slabby, and the product curve is tight enough to screen into two or three saleable grades without recirculating half the tonnage.
At 37 t the unit moves as one load, and it can run from its own engine or from site power. That dual option matters on remote benches where diesel is delivered by truck: running the cone off the mains when power is available cuts the fuel line item without changing the plant layout.
Material drops into the cavity between a manganese mantle and a bowl liner. The mantle is mounted on an eccentric shaft, so it gyrates rather than spins: the gap opens on one side while it closes on the other, and rock is squeezed continuously around the circumference. Because the crushing action is compressive and repeated, hard abrasive stone breaks along its grain instead of shattering, which is what gives the cubical shape.
With the chamber kept full, choke-fed, the rock breaks against other rock as much as against the liners. That inter-particle action is what produces a well-graded, low-flake product and spreads wear more evenly across the liner. The hydraulic system sets the discharge gap, releases tramp metal without stopping the plant, and clears the chamber if it does stall.
Requires external power supply
Built-in generator, diesel driven
China III / IV · EPA Tier 4 / Euro V
18-Month Warranty · Installation & Training · Remote Diagnostics · Spare Parts Supply
How this machine is paired with the rest of the plant, and what changes when the feed changes.
Specification sheets, the 18-month warranty terms and answers to the questions buyers ask first.
Download brochures & spec sheets › Watch the machines at work › Warranty & service programme › Crusher FAQ ›
The four questions buyers ask first about this machine - answered from the spec sheet, the cases library and the service programme.
It fits the contract. At 120–280 t/h and 37.3 t all-in, the HP200 runs on 223 kW installed - the extra 90 kW of an HP300 is paid for in fuel and chassis weight on a job that will never fill it.
Yes, once the on-board 4,800 × 2,160 mm screen closes the circuit: 0–5, 5–10 and 10–20 mm come off one pass depending on media and settings. The 8–44 mm figure is the chamber range; the screen decides the fractions that go to stockpile.
Liner life is set by feed abrasiveness and chamber choice. Wear packages are specified per project - the granite cases in the cases library show liner change-out intervals on abrasive duty - and replacement liners are quoted with the machine so cost per ton is known before purchase.
Standard build is 20 working days after deposit, before inland transport and sea freight; custom configurations are scheduled at drawing confirmation. A first liner set can be packed with the plant so a change-out never waits on a second shipment. Body warranty runs 18 months from commissioning or 3,000 operating hours, whichever comes first.
Specifications may vary depending on final configuration and project requirements. A dash or blank means the parameter is not listed for this model.
| Feeding section | |
|---|---|
| Feeding capacity | 200 t/h |
| Hopper volume | 3 m³ |
| Feeding belt (L×W) | 4,550×1,350 mm |
| Feeding height | 2,700 mm |
| Power | 5.5 kW×2 |
| Cone crusher | |
| Crusher model | HP200 cone crusher |
| Max feed particle size | 190 mm |
| Discharge range | 8–44 mm |
| Crusher weight | 12 t |
| Crusher power | 160 kW |
| Main belt | |
| Length × width | 11,000×1,600 mm |
| Discharge height | 3,500 mm |
| Power | 9.2 kW×2 |
| Finished belt (undersize belt) | |
| Length × width | 5,200×1,350 mm |
| Discharge height | 2,650 mm |
| Power | 5.5 kW×2 |
| Return material screen | |
| Screen size | 4,800×2,160 mm |
| Screen mesh size | 4,200×1,540 mm |
| Power | 3.7 kW×2 |
| Conveyor belts | |
| Transitional belt A (L×W) | 2,100×970 mm |
| Transitional belt A power | 3 kW |
| Return belt (L×W) | 8,930×770 mm |
| Return belt power | 5.5 kW |
| Complete machine | |
| Engine power | 100 kW / 400 kWDP |
| Overall weight | 37.3 t / 39.3 tDP |
| Machine processing capacity | 120–280 t/h |
| Total power of crushing work | 223 kW |
| Working dimensions (L×W×H) | 16,700×3,800×4,100 mm |
| Transportation dimensions (L×W×H) | 17,600×3,800×3,450 mm |
Tell us your raw material, required capacity, feeding size and final output size. Our engineer will recommend the suitable model for your project.
Your cookie choices
We store your choice on this device so we do not have to ask again. Analytics and marketing cookies stay off unless you allow them. Privacy Policy
EN