Mobile impact crushing solution
The SF-380D is a tracked impactor for rock that does not need to be squeezed: limestone, soft quarry stone, asphalt millings, demolition rubble. A 1214 rotor running 250 kW takes 600 mm feed down to 0–150 mm at 150–240 t/h, and the whole plant weighs 48.5 t. If the material is brittle, an impactor will out-produce a jaw-and-cone train of the same power on both tonnage and shape.
A short walk-around filmed on a customer site — feeding, crushing and discharge, so you can see how the machine actually runs before you shortlist it.
Watch more videosOne-pass reduction to a saleable sub-base or aggregate.
Concrete and masonry reduced in a single stage, steel pulled by the magnet.
Rounded millings without the flake a jaw produces.
Impactors get chosen for two reasons: they reduce a lot in one pass, and they produce a rounded particle. A jaw followed by a cone needs two machines and two drives to reach the same size; the SF-380D does it with one rotor, and the resulting aggregate has fewer flat faces, which is what most concrete and asphalt specs are really asking for.
The trade-off is wear. On abrasive rock, blow bars and impact plates are consumables, and the cost per tonne climbs quickly. On limestone, concrete and asphalt, where the material breaks easily, the same parts last far longer and the single-stage reduction is the cheaper route. This plant is built for that side of the line, and its place is urban recycling, quarry overburden and road reconstruction.
Material enters above the rotor and is caught by blow bars mounted on a fast-turning rotor. Instead of being squeezed, it is struck and thrown against the impact plates (aprons) above, then falls back into the rotor path and is struck again. Because the energy is applied as impact rather than compression, the stone separates along its natural weaknesses, its grain boundaries. That is why a brittle rock breaks cleanly and a rounded product comes out.
Product size is set by the gap between the rotor and the aprons. Closing the gap holds the material in the chamber longer and produces a finer curve; opening it raises tonnage with a coarser top size. The aprons also release hydraulically if something unbreakable enters, so the chamber clears itself instead of breaking the rotor.
Requires external power supply
Built-in generator, diesel driven
China III / IV · EPA Tier 4 / Euro V
18-Month Warranty · Installation & Training · Remote Diagnostics · Spare Parts Supply
How this machine is paired with the rest of the plant, and what changes when the feed changes.
Site conditions, throughput and the result the customer reported.
220 TPH C&D Recycling Plant in Thailand › 170TPH Limestone Crushing Plant in China › 170TPH Quarry Crushing Plant in Russia ›
Specification sheets, the 18-month warranty terms and answers to the questions buyers ask first.
Download brochures & spec sheets › Watch the machines at work › Warranty & service programme › Crusher FAQ ›
The four questions buyers ask first about this machine - answered from the spec sheet, the cases library and the service programme.
Impact, in one machine. A 1214 rotor at 250 kW takes 600 mm feed to 0–150 mm at 150–240 t/h and gives a cubical product without a secondary. The trade is wear: on abrasive rock the blow-bar cost per ton is higher than liners, which is when jaw-cone wins instead.
Yes, with the magnet ahead of the chamber to pull rebar out of the stream. Slabs and columns reduce in one pass; the limit is the 600 mm feed opening, so structural pieces are cut or broken down first if they will not enter the box.
Impact models are the standard choice for C&D recycling, typically with magnetic separation ahead of the chamber - the Thai recycling cases show the full setup. VSI units are shaping and sand machines: they belong after the demolition stream has already been cleaned and crushed.
Standard build is 20 working days after deposit, before inland transport and sea freight; custom configurations are scheduled at drawing confirmation. On contractor duty the bottleneck is usually wear parts, not the machine, so blow bars and rotors are quoted with the plant and air-freighted in 3-7 days when stock runs low. Body warranty runs 18 months from commissioning or 3,000 operating hours, whichever comes first.
Specifications may vary depending on final configuration and project requirements. A dash or blank means the parameter is not listed for this model.
| Feed section | |
|---|---|
| Feeding capacity | 230 t/h |
| Hopper volume | 5 m³ |
| Power | 4.5 kW×2 |
| Feeder size (L×W) | 3,550×1,280 mm |
| Feeding height | 3,850 mm |
| Impact crusher | |
| Crusher model | 1214 impact crusher |
| Feed inlet size (L×W) | 1,380×1,000 mm |
| Maximum feed particle size | 600 mm |
| Discharge range | 0–150 mm |
| Crusher weight | 18 t |
| Crusher power | 250 kW |
| Main belt | |
| Length × width | 9,600×1,600 mm |
| Discharge height | 2,900 mm |
| Power | 9.2 kW×2 |
| Finished belt | |
| Length × width | 5,200×1,350 mm |
| Discharge height | 2,600 mm |
| Power | 5.5 kW×2 |
| Return material screen | |
| Screen size | 4,600×2,160 mm |
| Screen layers | 1 |
| Power | 3.7 kW×2 |
| Conveyor belts | |
| Transition belt (L×W) | 1,750×770 mm |
| Transition belt power | 3 kW |
| Return belt (L×W) | 6,400×770 mm |
| Return belt power | 5.5 kW |
| De-ironing separator | |
| Length × width | 2,100×910 mm |
| Power | 4 kW |
| Complete machine | |
| Track chassis model | LDZ55-3657 |
| Engine power | 100 kW / 400 kWDP |
| Whole machine weight | 48.5 t / 50.5 tDP |
| Machine processing capacity | 150–240 t/h |
| Total power of crushing work | 308.3 kW |
| Working dimensions (L×W×H) | 16,600×3,500×4,000 mm |
| Transportation dimensions (L×W×H) | 16,600×3,500×3,750 mm |
Tell us your raw material, required capacity, feeding size and final output size. Our engineer will recommend the suitable model for your project.
Your cookie choices
We store your choice on this device so we do not have to ask again. Analytics and marketing cookies stay off unless you allow them. Privacy Policy
EN