Crushing and screening in one
The SF-380D-S is the SF-380D with a two-deck screen bolted onto the same chassis: 600 mm feed, 150–240 t/h, 1214 impactor at 250 kW, and two finished aggregate sizes coming off one 51.4 t plant. It removes the separate screener from the spread, along with a loader, a stockpile and one more machine to move between sites.
One machine, three finished aggregate sizes. Watch the closed-circuit impact plant crush, screen and recirculate oversize material in a single pass.
Watch more videosOne chassis, 7 m working width, fits a vacant lot.
Recycled 0–20 and 20–40 mm from a single pass.
One excavator feeds, two stockpiles come out.
A crusher and a screen on two chassis work fine until the site gets tight. That is the normal condition in urban recycling: a vacant lot, a street closure, a plant footprint hemmed in by buildings. On one chassis with a 7 m working width, the screening unit sits directly under the discharge, and the oversize returns to the chamber on an internal belt instead of a ground conveyor.
The result is two saleable grades from one machine and one operator. For a demolition contractor selling recycled 0–20 and 20–40 mm, that is the whole plant: feed it with an excavator, take two stockpiles out the back. Fuel, transport and manning all scale with one unit instead of two, which is usually the difference between a job that pays and one that does not.
The rotor strikes the material against the aprons, and the discharge falls straight onto a two-deck screen mounted on the same frame. The top deck takes out the coarse oversize and returns it to the crusher; the second deck splits the passing material into two grades. Because the return is internal and short, the circulating load is small and the plant reaches steady state quickly after start-up.
The screens run on the same hydraulic and electrical system as the crusher, so there is no second engine and no separate control. Deck changes are the only adjustment needed to move between product specifications. The crusher setting stays where it is, which makes the plant practical for a contractor who switches between a 0–20 sub-base and a 20–40 drainage stone within the same month.
Requires external power supply
Built-in generator, diesel driven
China III / IV · EPA Tier 4 / Euro V
18-Month Warranty · Installation & Training · Remote Diagnostics · Spare Parts Supply
How this machine is paired with the rest of the plant, and what changes when the feed changes.
Specification sheets, the 18-month warranty terms and answers to the questions buyers ask first.
Download brochures & spec sheets › Watch the machines at work › Warranty & service programme › Crusher FAQ ›
The four questions buyers ask first about this machine - answered from the spec sheet, the cases library and the service programme.
Not for two finished sizes. The 5,150 × 2,160 mm two-deck box sits on the same chassis and returns oversize to the rotor, so one 51.4 t plant produces two saleable fractions at 150–240 t/h - no second machine, no second operator, no stockpile between them.
About 2.9 t and 9 kW over the plain SF-380D: 51.4 t against 48.5 t, and 317.4 kW installed against 308.3 kW. That is the whole premium for removing a standalone screener and the loader that would feed it.
Impact models are the standard choice for C&D recycling, typically with magnetic separation ahead of the chamber - the Thai recycling cases show the full setup. VSI units are shaping and sand machines: they belong after the demolition stream has already been cleaned and crushed.
Standard build is 20 working days after deposit, before inland transport and sea freight; custom configurations are scheduled at drawing confirmation. On contractor duty the bottleneck is usually wear parts, not the machine, so blow bars and rotors are quoted with the plant and air-freighted in 3-7 days when stock runs low. Body warranty runs 18 months from commissioning or 3,000 operating hours, whichever comes first.
Specifications may vary depending on final configuration and project requirements. A dash or blank means the parameter is not listed for this model.
| Feed section | |
|---|---|
| Feeding capacity | 230 t/h |
| Hopper volume | 5 m³ |
| Power | 4.5 kW×2 |
| Feeder size (L×W) | 3,550×1,280 mm |
| Feeding height | 3,850 mm |
| Impact crusher | |
| Crusher model | 1214 impact crusher |
| Feed inlet size (L×W) | 1,380×1,000 mm |
| Maximum feed particle size | 600 mm |
| Discharge range | 0–150 mm |
| Crusher weight | 18 t |
| Crusher power | 250 kW |
| Screening module | |
| Screen size | 4,600×1,540 mm |
| Screen layers | 2 |
| Finished sizes | 2 aggregate sizes simultaneously |
| Main belt | |
| Length × width | 11,200×1,600 mm |
| Discharge height | 2,900 mm |
| Power | 9.2 kW×2 |
| Finished belt | |
| Length × width | 5,000×1,350 mm |
| Discharge height | 2,100 mm |
| Power | 5.5 kW×2 |
| Return material screen | |
| Screen size | 5,150×2,160 mm |
| Power | 5.5 kW×2 |
| Conveyor belts | |
| Side conveyor belt (L×W) | 5,150×800 mm |
| Side conveyor power | 5.5 kW |
| Transition belt (L×W) | 1,750×770 mm |
| Transition belt power | 3 kW |
| Return belt (L×W) | 7,300×970 mm |
| Return belt power | 5.5 kW |
| De-ironing separator | |
| Length × width | 2,100×910 mm |
| Power | 4 kW |
| Complete machine | |
| Track chassis model | LDZ55-3657 |
| Engine power | 100 kW / 400 kWDP |
| Whole machine weight | 51.4 t / 53.4 tDP |
| Machine processing capacity | 150–240 t/h |
| Total power of crushing work | 317.4 kW |
| Working dimensions (L×W×H) | 17,800×7,000×4,700 mm |
| Transportation dimensions (L×W×H) | 17,800×3,780×3,850 mm |
Tell us your raw material, required capacity, feeding size and final output size. Our engineer will recommend the suitable model for your project.
Your cookie choices
We store your choice on this device so we do not have to ask again. Analytics and marketing cookies stay off unless you allow them. Privacy Policy
EN