Modular primary crushing unit
The SE-J1060 is the 1060 jaw without the tracks: 700 mm feed, 180–350 t/h, 110 kW, 38 t. Same chamber and same throughput as the mobile unit, on a frame that bolts to a foundation or a skid. It is the choice for a quarry that has already decided where the primary goes, and would rather spend the difference on a screen or a stockpile conveyor.
A short walk-around filmed on a customer site — feeding, crushing and discharge, so you can see how the machine actually runs before you shortlist it.
Watch more videosReplaces an ageing jaw in a line that already has the civils.
Skid-mounted and moved with a loader as the pit advances.
Constant-speed electric drive for a steady product curve.
A tracked plant earns its cost when the machine moves. When it does not move for years, the undercarriage is dead capital and the engine is a second maintenance schedule. The SE-J1060 keeps the crushing performance and drops both: electric drive, fixed frame, 38 t instead of 45.5 t, and a 0–180 mm discharge range that suits a secondary cone downstream.
It also slots into an existing plant more cleanly than a crawler. The frame accepts a standard feeder and discharge conveyor, so the unit can replace an ageing primary in a line that already has the civils: same footprint, no re-permitting of the haul road layout. For semi-mobile setups it can be skid-mounted and moved with a loader when the pit pushes forward.
Material enters the 1060 chamber and is compressed between the fixed and moving jaw plates. The eccentric shaft produces the closing stroke; the toggle plate holds the geometry and acts as the mechanical fuse, failing before the frame does if something unbreakable gets in. Reduction happens along the full height of the chamber, so the rock is broken progressively rather than in one hit at the top.
Discharge size is controlled at the opening, and with the setting range widened to 180 mm the unit can be run coarse for secondary feed or fine for direct product. Because the frame is fixed, there is no track flex under load and no engine speed to manage; the motor runs at constant speed from the mains, which keeps the product curve steady across the shift.
Requires external power supply
Built-in generator, diesel driven
China III / IV · EPA Tier 4 / Euro V
18-Month Warranty · Installation & Training · Remote Diagnostics · Spare Parts Supply
How this machine is paired with the rest of the plant, and what changes when the feed changes.
Jaw + cone line for hard rock › Jaw + impact line for soft rock ›
Specification sheets, the 18-month warranty terms and answers to the questions buyers ask first.
Download brochures & spec sheets › Watch the machines at work › Warranty & service programme › Crusher FAQ ›
The four questions buyers ask first about this machine - answered from the spec sheet, the cases library and the service programme.
38 t instead of 45.5 t, no undercarriage and no engine, and a 5 m³ hopper against 3 m3. In practice the modular unit takes a direct loader or truck dump and runs on mains power, which is what a quarry with a fixed primary position wants.
It is a bolt-down frame, not a poured foundation: unbolt, lift, re-levelling on the new pad. That is cheaper than moving a tracked plant only when the move is rare - the tracks on the mobile 1060 are paid for by regular site changes, not by one.
The jaw uses a toggle-based relief path: un-crushable objects pass through instead of destroying the frame, and the chamber clears without a lengthy stoppage. The specific protection configuration of the SE-J1060 is listed in the spec table above.
Standard build is 20 working days after deposit, before inland transport and sea freight; custom configurations are scheduled at drawing confirmation. Because jaw frames are weld-heavy, we load-test the complete plant before dispatch. The machine carries an 18-month body warranty from commissioning or 3,000 operating hours, whichever comes first.
Specifications may vary depending on final configuration and project requirements. A dash or blank means the parameter is not listed for this model.
| Feeding equipment | |
|---|---|
| Feeding capacity | 180–350 t/h |
| Maximum feeding size | 700 mm |
| Feeding height | 3,800 mm |
| Hopper volume | 5 m³ |
| Vibrating feeder (L×W) | 4,150×1,200 mm |
| Motor model | PJMV-65-6 |
| Power | 4.5 kW×2 |
| Jaw crusher | |
| Crusher model | 1060 jaw crusher |
| Feed inlet (L×W) | 1,060×750 mm |
| Maximum feed particle size | 700 mm |
| Crusher weight | 18 t |
| Discharge range | 0–180 mm |
| Main bearing model | 23060 |
| Main motor model | YE3-160L-6 |
| Crusher power | 110 kW |
| Main belt | |
| Stacking height | 2,800 mm |
| Length × width | 10,600×1,350 mm |
| Electric roller model | M1-270 |
| Power | 9.2 kW×2 |
| Tail belt | |
| Stacking height | 2,450 mm |
| Width | 800 mm |
| Electric roller model | M1-270 |
| Power | 5.5 kW |
| De-ironing separator | |
| Length × width | 2,100×910 mm |
| Power | 4 kW |
| Complete machine | |
| Whole machine weight | 38 t |
| Processing capacity | 180–350 t/h |
| Total power of crushing operation | 146.9 kW |
| Working dimensions (L×W×H) | 15,150×6,250×3,450 mm |
| Transportation dimensions (L×W×H) | 15,150×3,150×3,450 mm |
Tell us your raw material, required capacity, feeding size and final output size. Our engineer will recommend the suitable model for your project.
Your cookie choices
We store your choice on this device so we do not have to ask again. Analytics and marketing cookies stay off unless you allow them. Privacy Policy
EN