High-capacity primary crushing
The SE-1060 is the standard primary for a working quarry: a 1060 jaw with a 700 mm feed opening, 180–350 t/h, 110 kW on the crusher and a 90 kW engine, 45.5 t on tracks. It is sized so that a granite or basalt face can be blasted to a normal pattern and fed straight in, without a secondary break or a hydraulic hammer standing over the hopper.
A short walk-around filmed on a customer site — feeding, crushing and discharge, so you can see how the machine actually runs before you shortlist it.
Watch more videosGranite, basalt, andesite, gravel, iron ore, copper ore, etc.
Limestone, gravel, diabase, coal, etc.
Construction waste
Most quarries pick a primary on one number, then live with the consequences. A 700 mm opening matches a 3 m bench pattern, so oversize becomes the exception instead of the daily routine. With the discharge set between 80 and 250 mm, the unit can either feed a cone at a sensible reduction ratio or produce a sub-base product on its own.
The plant is a full spread on one chassis: vibrating feeder with a pre-screen that bypasses fines before they reach the jaw, side conveyor for the bypassed material, magnet over the main belt for rebar and bucket teeth, and a 15.5 m transport length that stays inside a standard low-bed permit. That matters on quarry moves, where the cost is in the permits and the days, not in the crushing.
Feed is metered into the 1060 chamber by a vibrating feeder. A grizzly section ahead of the jaw takes out the fines and the dirt so the chamber only does the work it is good at; the bypassed material rejoins the product stream on the side conveyor. Inside, the eccentric shaft drives the moving jaw in an elliptical path and the rock is loaded in compression against the fixed plate.
Because the reduction is by compression, the SE-1060 handles granite, basalt and abrasive river gravel without the impact wear a hammer-type primary would suffer. The 80–250 mm setting range covers both secondary feed and direct sub-base production, and the hydraulic opening lets the setting be changed between jobs without pulling the toggle.
Requires external power supply
Built-in generator, diesel driven
China III / IV · EPA Tier 4 / Euro V
18-Month Warranty · Installation & Training · Remote Diagnostics · Spare Parts Supply
How this machine is paired with the rest of the plant, and what changes when the feed changes.
Jaw + cone line for hard rock › Jaw + impact line for soft rock ›
Site conditions, throughput and the result the customer reported.
200TPH River Pebble Crushing Plant in Indonesia › 200TPH Marble Crushing Plant in Thailand › 220 TPH Granite Aggregate Plant in Guangdong ›
Specification sheets, the 18-month warranty terms and answers to the questions buyers ask first.
Download brochures & spec sheets › Watch the machines at work › Warranty & service programme › Crusher FAQ ›
The four questions buyers ask first about this machine - answered from the spec sheet, the cases library and the service programme.
Because the blast pattern decides it. A 700 mm opening matches a normal quarry round at 180–350 t/h and 146.9 kW installed; if the face genuinely produces 800 mm rock the 1160 is the right unit, and if it does not, the bigger chamber is 2.5 t of chassis you never fill.
Yes - the discharge setting runs from 80 mm, so the belt can go straight into a secondary cone hopper in a two-stage train. Where the plant sells graded aggregate, the screen sits between the two stages instead, so the cone only sees material that needs reducing.
The jaw uses a toggle-based relief path: un-crushable objects pass through instead of destroying the frame, and the chamber clears without a lengthy stoppage. The specific protection configuration of the SE-1060 is listed in the spec table above.
Standard build is 20 working days after deposit, before inland transport and sea freight; custom configurations are scheduled at drawing confirmation. Because jaw frames are weld-heavy, we load-test the complete plant before dispatch. The machine carries an 18-month body warranty from commissioning or 3,000 operating hours, whichever comes first.
Specifications may vary depending on final configuration and project requirements. A dash or blank means the parameter is not listed for this model.
| Feeding equipment | |
|---|---|
| Feeding capacity | 180–350 t/h |
| Maximum feeding size | 700 mm |
| Feeding height | 3,600 mm |
| Hopper volume | 3 m³ |
| Vibrating feeder (L×W) | 4,000×1,100 mm |
| Vibrating feeder motor | PJMV-65-6 |
| Vibrating feeder power | 4.5 kW×2 |
| Jaw crusher | |
| Crusher model | 1060 jaw crusher |
| Feed inlet (L×W) | 1,060×750 mm |
| Maximum feed particle size | 700 mm |
| Crusher weight | 18 t |
| Discharge range | 80–250 mm |
| Main bearing model | 23060 |
| Main motor model | YE3-315L-6 |
| Crusher power | 110 kW |
| Main belt | |
| Stacking height | 3,000 mm |
| Width × length | 9,500×1,350 mm |
| Electric roller model | M1-270 |
| Power | 9.2 kW×2 |
| Tail belt | |
| Stacking height | 2,350 mm |
| Width | 880 mm |
| Electric roller model | M1-270 |
| Power | 5.5 kW |
| De-ironing separator | |
| Length × width | 2,100×910 mm |
| Power | 3 kW |
| Complete machine | |
| Engine power | 90 kW / 200 kWDP |
| Track chassis model | LDZ55-3657 |
| Whole machine weight | 45.5 t / 47.5 tDP |
| Processing capacity | 180–350 t/h |
| Total power of crushing operation | 146.9 kW |
| Working dimensions (L×W×H) | 15,480×4,150×3,950 mm |
| Transportation dimensions (L×W×H) | 15,480×3,180×3,950 mm |
Tell us your raw material, required capacity, feeding size and final output size. Our engineer will recommend the suitable model for your project.
Your cookie choices
We store your choice on this device so we do not have to ask again. Analytics and marketing cookies stay off unless you allow them. Privacy Policy
EN