Dual-core crushing performance
The TZ6510 puts two jaw assemblies in one housing. Feed up to 500 mm goes in and comes out at 65–185 mm in a single pass, at 80–300 t/h and up to a 15:1 reduction, normally reached only by running a jaw and then a secondary. For plants that need two stages of reduction but have no room, no budget, or no power for two machines, this is the shortcut.
A short walk-around filmed on a customer site — feeding, crushing and discharge, so you can see how the machine actually runs before you shortlist it.
Watch more videosA conventional jaw gives you 4:1 to 6:1. Getting to 15:1 means a second crusher, a second drive, more conveyors, and a taller structure. On a quarry bench, a recycling yard, or a mine backfill operation where the footprint is fixed, that second stage often does not fit. The TZ6510 folds it into one frame: the first jaw pre-breaks, the second reduces, and the product leaves at a size the screen can handle.
The 132 kW drive and 12 t crusher weight (motor excluded) mean it can be mounted where a two-machine train could not go, and it draws less than the two motors it replaces. Fewer drives, fewer belts, fewer transfer points; in practice that is fewer places to break down and fewer points to generate dust.
Two movable jaws sit symmetrically in a V-shaped chamber, one at the feed side and one at the outlet, and both are driven from the same eccentric shaft through belts so they move in unison. The feed-side jaw grips and compresses the rock as it enters; the outlet-side jaw keeps reducing it as it travels down. The stroke therefore runs the full length of the cavity instead of ending at the throat, which is where a conventional jaw loses its force.
The practical result is a product curve closer to a secondary crusher than to a primary jaw, and a reduction ratio that lets a single machine feed a screen directly. Wear is spread across two sets of plates rather than concentrated on one, and because the second set only sees pre-broken rock, its plates see lighter, more even loading than a primary plate would.
Requires external power supply
Built-in generator, diesel driven
China III / IV · EPA Tier 4 / Euro V
18-Month Warranty · Installation & Training · Remote Diagnostics · Spare Parts Supply
How this machine is paired with the rest of the plant, and what changes when the feed changes.
Jaw + cone line for hard rock › Jaw + impact line for soft rock ›
Specification sheets, the 18-month warranty terms and answers to the questions buyers ask first.
Download brochures & spec sheets › Watch the machines at work › Warranty & service programme › Crusher FAQ ›
The four questions buyers ask first about this machine - answered from the spec sheet, the cases library and the service programme.
A whole stage. Feed up to 500 mm comes out at 65–185 mm in one pass, up to 15:1 reduction at 80–300 t/h, on 132 kW. A jaw plus a secondary reaches the same ratio with two machines, two drives and the belt and screen between them.
When shape or abrasion decides the economics. Dual-core buys reduction and throughput, not cubical product: on granite that has to sell as 10–20 mm, a jaw-cone train still wins on particle shape and on liner cost per ton.
The jaw uses a toggle-based relief path: un-crushable objects pass through instead of destroying the frame, and the chamber clears without a lengthy stoppage. The specific protection configuration of the TZ6510 is listed in the spec table above.
Standard build is 20 working days after deposit, before inland transport and sea freight; custom configurations are scheduled at drawing confirmation. Because jaw frames are weld-heavy, we load-test the complete plant before dispatch. The machine carries an 18-month body warranty from commissioning or 3,000 operating hours, whichever comes first.
Specifications may vary depending on final configuration and project requirements. A dash or blank means the parameter is not listed for this model.
| Jaw crusher | |
|---|---|
| Crusher model | TZ6510 dual-core jaw crusher |
| Listed capacity | 80–300 TPH |
| Processing capacity | 80–300 t/h |
| Maximum feed size | 500 mm |
| Crusher feed inlet (L×W) | 650×1,000 mm |
| Discharge range | 65–185 mm |
| Crusher power | 132 kW |
| Crusher weight | 12 t (excluding motor) |
| Complete machine | |
| Working dimensions (L×W×H) | 3,583×1,964×2,536 mm |
Tell us your raw material, required capacity, feeding size and final output size. Our engineer will recommend the suitable model for your project.
Your cookie choices
We store your choice on this device so we do not have to ask again. Analytics and marketing cookies stay off unless you allow them. Privacy Policy
EN